Although the Wizard had the same general look about it throughout its long production life, the action varied considerably. Understandably, the natural whole cane butt sections vary in diameter, but more surprisingly, there are also considerable differences between the split cane sections from period to period. You would think that Allcocks would have made all their Wizards to set sizes, but they certainly didn’t. Armed with a digital vernier gauge, I have found huge (by rod-making standards) differences between the blanks. The rods therefore vary considerably in character, from an easy though action, to quite tippy. A small butt with a heavy tip produces quite a floppy feel: a heavy butt (some are thicker than Avocets) with a steep taper middle, and a light tip, produces a stiffer, tippier feel. They’re all lovely, but some are lovelier than others. Continuation of articleA few late Wizards have an improved 20” handle length, (too little, too late) and bored shive corks rather than original  sheet-cork covered pine version. Many late Allcocks rods, including Wizards, were fitted with tapered but unserrated ferrules. They are strong, but because of the sudden transition to the cane surface, they tend to produce cracking of the varnish at that interface. There are two remedies: the ferrules can be replaced, or serrations carefully cut into the ferrules. This can only be done properly and safely with the ferrules off the rod.

 

The standard rod has (two) too few rings, but this is easily remedied. The Super Wizard has agate lined rings throughout (again too few). These rings look very up-market, but they are also very heavy, and quite unsuitable for the light tip section. I always replace them all with standard chrome-plated stainless steel, high or low rings, and this makes the rod feel far less floppy.

 

My opinions about the standard Wizard handle are well known. Whilst I am aware that this may be seen by rod historians as a Barbaric heresy, I have to say that I believe the Wizard (and Wizard style rods of all makes) is profoundly improved by replacing the standard 17” handle with a new 21” version. B. James knew this when they brought out their lovely Avocet model: effectively a modified Wizard taper, with a long (24”) handle.

 

Using the basic Allcocks’ Wizard as a basis for meddling, all sorts of wonderful rods can emerge. Beyond the top of the handle the rod tapers should be considered sacrosanct, but by replacing the decidedly stiff short handle with an extension of whole cane a much more lithe rod is produced. A longer stiff handle makes the whole rod quite beefy.

 

Early in the day, Allcocks recognised the new convenience of fixed spool reels, and the Wizard was oft-times illustrated with a ‘threadline’ reel attached. Despite this manufacturer-approved status, I find it somehow discordant to attach anything other than a centre-pin to a Wizard. My favourite is a 3½” pre-war Aerial, which fits just so for size and appearance. Given a following wind, and using the particularly appropriate Wallis cast, I can cast a three swan-shot rig thirty yards with this outfit. The rod is equally happy as a light leger rod, with a natural affinity for chub under trees. Wizard aficionados sometimes have a Wizard especially equipped with bells life, or full open bridge rings, which are more suitable for legering, because they put less twisting moment into the rod.

 

The ULTIMATE Allcocks Wizard, I mean, the one that all collectors would kill for, is the Black Label Wizard. I have seen only one, and that was forty years ago, in a shop window in Staplehurst, Kent. The BLW was made (according to Tony Croft, who was a rodmaker at Allcocks for much of his working life) in the late 1930’s. The one I saw had a long whole cork handle, with brass fittings, and a black Allcocks oval, with gold lettering. It was gorgeous. One enthusiast told me that only a few were ever made, and that the black label was in honour of a dead  Allcock. It’s a good story, whatever the truth of it. A few BLW reproductions have been made over the years, and they are VERY desirable.  Then to cap it all, there are the very few ‘Wallis Wizards’ made by Bob Southwell (The Captain) of Croydon . If you ever handle one you will know why they, are the sprung steel ultimate, of ultimate  Wizards.                    Return to home page